|
|
| |
 |
MaxEmerge Plus, XP, Pro
Includes most 1700 series planters made from late 1990's to current. The wheels are attached to the planter with a 5/8" or 16mm bolt with spacers/washers to adjust spacing.
Note: Some early 1700 MaxEmerge 2 series planters require different wheels. MaxEmerge (7000-7100) and MaxEmerge 2 (7200-7300-early 1700) that have upgraded tailpieces will usually use this wheel style. Please call us if you have any questions and we will be happy to find the correct wheel for your specific planter.
Mounting hardware is not included as the existing OEM hardware and spacers may be reused. If you require new hardware please order it through John Deere.
|
 |
Part Number: PW-193NT |
Price: $155.00 / row |
|
|
| |
|
MaxEmerge 2
Includes model 7200, 7300 & early 1700 series planters. The wheels are mounted over a shaft on the tailpiece and are held on with left and right hand nuts. The original dust cap may be used with these wheels.
Note: Some planters have been updated to newer cast iron tailpieces and require PW-193NT (see above). Please call us if you have any questions and we will be happy to find the correct wheel for your specific planter.
Mounting hardware is not included as the existing OEM hardware may be reused. Wheels do include hardware shown below to bolt the center hub to outer ring. If you require new hardware please order it through John Deere.
|
|
Part Number: PW-066NT
|
| Price: $165.00 / row |
|
|
| |
|
MaxEmerge
Includes model 7000 & 7100 series planters. The wheels are attached via the bearing spindle sliding into a tube on the tailpiece and are fastened with 1/4" roll pins.
Note: Some planters have been updated to newer tailpieces and require PW-193NT (see above). If your tailpieces are worn out we highly recommend you update to newer aftermarket tailpieces. Please call us if you have any questions and we will be happy to find the correct wheel for your specific planter.
Mounting hardware is not included as the existing OEM hardware may be reused. Wheels do include hardware shown below to bolt the center hub to outer ring. If you require new hardware please order it through John Deere.
|
 |
Part Number: PW-065NT |
| Price: $165.00 / row |
|
|
| |
|
 |
1993-CURRENT
Wheels are fastened on with a 5/8" or 16mm bolt with spacers/washers to adjust spacing.
Mounting hardware is not included as the existing OEM hardware and spacers may be reused. If you require new hardware please order it through Kinze.
|
|
Part Number: PW-193NT |
| Price: $155.00 / row |
|
|
| |
|
Optional Kinze Meshing Kit
Some Kinze planters (such as Model 2600) will not allow our wheels to mesh due to tailpiece design. Therefore we have a Meshing Kit to correct wheel alignment for these planters. The kit is only required if you want to mesh our wheels together. The kit comes with all required hardware and two corrective alignment plates. |
 |
Part Number: PW-227 |
| Price: $18.00 / row |
| |
| |
|
| |
|
1992 & EARLIER
Wheels are mounted by the bearing spindle which slides into the tube on the tailpiece and are fastened with 1/4" roll pins.
Mounting hardware is not included as the existing OEM hardware may be reused. Wheels do include hardware shown below to bolt the center hub to outer ring. If you require new hardware please order it through Kinze.
|
|
Part Number: PW-065 NT |
| Price: $165.00 / row |
| |
| |
| |
|
| |
 |
6000 & 8000 SERIES
Wheels are mounted with a 5/8" or 16mm bolt with spacers/washers to adjust spacing.
Note: White Planters with a SINGLE WIDE closing wheel system will not work with Posi Close Wheels. We recommend converting the planter to the "V" style dual wheel system. We do not carry a conversion kit for White, however, one can be obtained through White. Once single wheel systems are converted PW-193NT wheels will fit onto the planter.
Mounting hardware is not included as the existing OEM hardware and spacers may be reused. If you require new hardware please order it through White.
|
|
Part Number: PW-193NT |
List Price: 155.00 / row |
|
|
| |
 |
800-900 & 1200 SERIES
These planters have a single wide closing wheel system. They must be converted to the "V" style dual wheel system to accommodate our Posi Close Wheels. Conversion can be done via our PW-293 kit. The kit requires removal of existing arms and wheel. It can, however, be used with or without the original planter closing disks.
Order one conversion kit and one pair of wheels per row. The mounting hardware for the wheels is included in the conversion kit.
|
 |
Part Number: PW-293 Conversion Kit |
| Price: $75.00 / row |
|
Part Number: PW-193NT Wheels |
| Price: $155.00 / row |
|
|
| |
 |
NG+2 / Upgraded NG+ (Requires Monosem Tailpiece Upgrade Kit for NG+ planters)
Wheels are mounted with a 5/8" or 16mm bolt with spacers/washers to adjust spacing.
Mounting hardware is not included as the existing OEM hardware and spacers may be reused. If you require new hardware please order it through us or you local Monosem dealer.
|
|
Part Number: PW-193NT |
| Price: $155.00 / row |
|
|
| |
|
Monosem NG+ Tailpiece Upgrade Kit
An upgrade kit is required to use Posi Close wheels on Monosem Ng+ planters with drilled rod adjustable tailpieces. Once the tailpiece is upgraded order PW-193NT Closing Wheels above.
The Tailpiece Upgrade Kit includes:
1x 7080.S Bracket
2x 900159 Bushing spacer, standard 7/16" wide
1x 30513015 Bolt, 16 x 80, RH
1x 30513115 Bolt, 16 x 80, LH
We also recommend replacing Monosem Part # 7093 "Pivot Pin" if it shows wear when the tailpiece kit is being installed. The pin can be ordered separately below:
|
 |
Part Number: Monosem - Tail |
Part Number: 7093 - Pivot Pin |
Price: $75.00 |
Price: $11.00 |
|
|
| |
| |
| |
|
|
| |
